SMT processing and manufacturing and soldering quality problems and handling methods

SMT processing and manufacturing involves many links, from the basic concept of PCB, to the difference between SMT and THT processes, to the analysis and solution of quality problems in various soldering processes.

<！--[if！支持列表]-->1.     <！--[endif]-->SMT is related to the THT process

<！--[if！支持列表]-->·       <！--[endif]-->PCB is an important support and electrical connection provider of electronic components, and the SMT process is fundamentally different from the traditional THT process in terms of assembly technology, which is reflected in "pasting" and "plugging". THT uses leaded components, and the SMT circuit board assembly density is greatly increased by inserting the component leads into the PCB through holes and soldering on the other side of the substrate, while the SMT solder joints are on the same side of the board as the components. DIP packaging is one of the THT plug-in processes, and the trend of high-performance computing packaging is shifting from FCBGA and 2.5D packaging to 3D packaging, and electronic components are redesigned to SMDs that can be soldered directly to PCBs or other substrate surfaces.

<！--[if！支持列表]-->2.     <！--[endif]-->SMT dispensing process defects and solutions

<！--[if！支持列表]-->·       <！--[endif]-->In the SMT dispensing process, there are common defects such as component displacement, wafer drop after wave soldering, and floating/displacement of component pins after curing.

<！--[if！支持列表]-->·       <！--[endif]-->The causes of component displacement include uneven amount of adhesive output from the SMT, component displacement or low initial adhesion during SMT, and long PCB placement time, etc., and the solution is to check the nozzle, adjust the placement machine, change the glue, and control the PCB placement time.

<！--[if！支持列表]-->·       <！--[endif]-->Falling off after wave soldering is due to insufficient curing process parameters, large component size, aging of curing lamps, insufficient glue volume, contamination of components/PCBs, etc., which can be solved by adjusting the curing curve, checking the curing lamp, and considering the amount of glue and component/PCB contamination.

<！--[if！支持列表]-->·       <！--[endif]-->After curing, the floating/displacement of the component pins is caused by uneven placement adhesive, excessive amount, or component deviation during placement, and the solution is to adjust the dispensing and placement process parameters.

<！--[if！支持列表]-->3.     <！--[endif]-->Solder paste printing quality

<！--[if！支持列表]-->·       <！--[endif]-->Poor printing of solder paste will lead to a variety of quality problems, such as insufficient 焊膏 will cause insufficient amount of solder in solder joints, open circuits of components, etc.; Adhesion can lead to short-circuits, etc.; The overall deviation of printing leads to poor welding of the whole board components; Pulling the tip can cause a short circuit.

<！--[if！支持列表]-->·       <！--[endif]-->There are many factors that lead to the shortage of solder paste, including the printing press does not replenish the solder paste in time, the quality of the solder paste is abnormal, the expired use, the circuit board is problematic, the fixed clamp is loose, the problem of missing the printing screen, the scraper and the screen plate are damaged, the equipment parameter setting is not appropriate, and the artificial touch is removed.

<！--[if！支持列表]-->·       <！--[endif]-->The main factors of solder paste adhesion are circuit board design defects, stencil problems, failure to wipe clean, poor solder paste performance, loose fixing and clamping, inappropriate equipment parameter settings, artificial extrusion and adhesion, etc.

<！--[if！支持列表]-->·       <！--[endif]-->The main factors of the overall deviation of solder paste printing are the problem of the positioning reference point of the circuit board, the misalignment with the reference point of the screen board, the loose fixing clamp, the lack of positioning thimble, the failure of the optical positioning system of the printing machine, and the inconsistency between the opening of the screen and the design documents.

<！--[if！支持列表]-->·       <！--[endif]-->The main factors of printing solder paste are solder paste performance parameter problems, demoulding parameter setting problems, and burrs on the hole wall of the missing printing screen plate.

<！--[if！支持列表]-->4.     <！--[endif]-->SMT patch quality is related

<！--[if！支持列表]-->·       <！--[endif]-->The common quality problems of SMT patch include missing parts, side parts, turning parts, deviations, damaged parts, etc.

<！--[if！支持列表]-->·       <！--[endif]-->The factors that lead to missing parts include insufficient feeding of component feeding racks, component nozzle problems, equipment gas circuit failures, poor circuit board purchases, solder paste problems on pads, component quality problems, placement machine program errors and omissions, etc.

<！--[if！支持列表]-->·       <！--[endif]-->The main factors of turning parts and side parts during SMC resistor placement are abnormal feeding of the feeding rack, wrong nozzle height, wrong grasping height, too large size of the component taping charging hole, and reverse direction of bulk material.

<！--[if！支持列表]-->·       <！--[endif]-->The misalignment of the component is due to the incorrect coordinates of the placement machine and the unstable suction of the chip nozzle when the placement machine is programmed.

<！--[if！支持列表]-->·       <！--[endif]-->The damage during component placement is caused by the positioning of the ejector pin is too high, the Z-axis coordinate is incorrect when the placement machine is programmed, and the nozzle spring is stuck.

<！--[if！支持列表]-->5.     <！--[endif]-->Factors that affect the quality of SMT reflow soldering

<！--[if！支持列表]-->·       <！--[endif]-->In terms of solder paste, the quality of reflow soldering is greatly affected, such as the shape of alloy powder particles is related to the welding quality of narrow-pitch devices, the viscosity and composition should be appropriate, and the use specification after refrigerated storage should be paid attention to.

<！--[if！支持列表]-->·       <！--[endif]-->In terms of welding equipment, the vibration of the conveyor belt of reflow soldering equipment is too large, which affects the welding quality.

<！--[if！支持列表]-->·       <！--[endif]-->The reflow soldering process itself will lead to quality abnormalities such as cold welding, solder beads, tinning, cracks, etc., each with its own corresponding causes and solutions.

<！--[if！支持列表]-->·       <！--[endif]-->The fundamental cause is the unbalanced wetting force on both sides of the component, which is related to the design and layout of the pad, solderpaste and printing, chip displacement, furnace temperature curve, oxygen concentration in nitrogen reflow soldering and other factors, and there are corresponding solutions.

<！--[if！支持列表]-->·       <！--[endif]-->Solder beads can be divided into two categories, and the causes include incorrect temperature profiles, solder paste quality problems, printing and placement problems, etc., and solutions are also given for these reasons.

<！--[if！支持列表]-->·       <！--[endif]-->The wicking phenomenon is mostly seen in vapor phase reflow soldering, which is mainly caused by the high thermal conductivity of component pins, and the solutions include preheating, checking the solderability of PCB pads, and paying attention to component coplanarity.

<！--[if！支持列表]-->·       <！--[endif]-->Bridging can cause short circuits in components due to solder paste quality problems, printing system problems, excessive placement pressure, and rapid heating up of reflow ovens.

<！--[if！支持列表]-->

<！--[if！支持列表]-->

<！--[if！支持列表]-->

<！--[if！支持列表]-->6.     <！--[endif]-->Wave soldering quality defects and solutions

<！--[if！支持列表]-->·       <！--[endif]-->Drawing the tip is a defect unique to wave soldering, and the cause is related to the PCB transfer speed, preheating temperature, tin pot temperature, etc., and the solution is to adjust the relevant parameters, optimize the nozzle, etc.

<！--[if！支持列表]-->·       <！--[endif]-->The causes of virtual soldering include a variety of factors such as poor solderability of component leads, and the solution is to adjust these factors.

<！--[if！支持列表]-->·       <！--[endif]-->The cause of tin thinness is related to the solderability of component leads, pad size, etc., and there are corresponding solutions.

<！--[if！支持列表]-->·       <！--[endif]-->The causes and solutions of missing soldering are also given according to the solderability of the leads, wave device, 通量, etc.

<！--[if！支持列表]-->·       <！--[endif]-->The fundamental reason for the blistering of the solder mask film of the printed board after welding is the presence of gas or water vapor between the solder mask mold and the PCB substrate, which is related to the PCB processing process, storage environment, preheating temperature and other factors.

<！--[if！支持列表]-->·       <！--[endif]-->The reasons for open circuit or virtual soldering after IC pin soldering include poor coplanarity, poor pin solderability, poor 焊膏 quality, high preheating temperature, small printing template window size, etc., the solution is to pay attention to device storage, check solderability, control template window size, etc.

To sum up, the quality problems of SMT processing and manufacturing and welding are complex and diverse, and it is necessary to strictly control each link, accurately analyze the causes of different quality problems and take effective solutions to ensure the quality of SMT processing and manufacturing.